• Send Us a Message
    • Skip to content
    Nintendo Switch Console Sensor Rail Joy-Con Slide Rail Pair Left Right HAC-001 V2 Charging Flex Screen Replacement JPC MOBILE

    Nintendo Switch Console Sensor Rail Joy-Con Slide Rail Pair Left Right HAC-001 V2 Charging Flex

    $0.00 - $0.00
    $0.00
    $15.60
    $15.60 - $15.60
    $15.60
    SKU Pull-LRSlider-Switch
    Professional Repair Part

    Nintendo Switch Joy-Con Sensor Rail ā€” Console Slide Rail Pair

    Left & Right console-side rails with charging flex cable. Fits original Switch HAC-001 (2017) and HAC-001(-01) V2 (2019). Fixes Joy-Con not detected, not charging, loose fit, intermittent disconnect.

    HAC-001 + V2 Compatible Left + Right Pair Pre-Tested A-Grade Brisbane Stock
    Symptoms It Fixes Fitment Diagnose First Tech Specs Tools Required FAQs
    šŸ”§

    Brisbane Technical Hub

    Held in stock at our Forest Lake repair lab. Tech support from real Switch repairers.

    āœ…

    Authenticity Guaranteed

    A-grade pull rails harvested from original Switch consoles. Continuity-tested before dispatch.

    šŸšš

    Reliable Dispatch

    Ships 2-4 business days Australia-wide. Tracked shipping from Brisbane.

    Symptoms This Sensor Rail Fixes

    A worn or damaged console sensor rail is the most common cause of these Switch faults:

    Joy-Con Not Detected

    Console shows controller as missing even when slid on.

    Joy-Con Won't Charge

    Battery stays flat even when attached to a powered console.

    Loose or Wobbly Fit

    Joy-Con slides on but rattles in handheld mode.

    Mid-Game Disconnect

    Controller drops out under movement or bumps.

    Won't Lock In Place

    Latch fails so Joy-Con slides off freely.

    Sync Errors / SL+SR Faults

    SL or SR shoulder buttons not registering through the rail.

    Diagnose Before You Order

    Confirm the fault is the console rail, not the Joy-Con itself. Two-minute swap test:

    1. Slide a known-good Joy-Con of the same side onto the faulty rail.
    2. If the good Joy-Con also fails, the console rail is the cause. Order this part.
    3. If the good Joy-Con works fine, the fault sits inside the original Joy-Con.
    4. Test both left and right separately. They are independent rails on different flex cables.

    Fitment ā€” What This Part Fits

    āœ… Fits These Models

    • Nintendo Switch original ā€” model HAC-001 (2017 launch)
    • Nintendo Switch V2 ā€” model HAC-001(-01) (2019 extended battery)
    • Both V1 and V2 use the identical sensor rail assembly
    • Replaces both left and right console rails as a pair

    āŒ Does NOT Fit

    • Nintendo Switch OLED ā€” model HEG-001 uses a different rail design ā€” see Switch OLED parts
    • Nintendo Switch Lite ā€” model HDH-001 (no detachable Joy-Cons)
    • Nintendo Switch 2 ā€” model HEG (new rail system)
    • Joy-Con-side charging rail ā€” this is the console-side part only

    Technical Specifications

    Part Type
    Console-side sensor rail with flex cable
    Quantity
    Pair ā€” 1 Ɨ left rail + 1 Ɨ right rail
    Compatible Console
    Switch HAC-001 + HAC-001(-01) V2
    Assembly
    Plastic slide rail + integrated flex connector
    Function
    Joy-Con detect, sync data, charging current
    Mounting Screws
    4 Ɨ Y00 tri-wing 6.3 mm rear panel screws
    Latch Mechanism
    Spring-loaded lock with sensor pin contact
    Grade
    A-grade pull, continuity-tested
    Repair Difficulty
    Moderate ā€” 30 to 60 minutes
    Skill Level
    Intermediate ā€” micro-soldering not required
    Warranty
    7-day DOA cover from delivery
    Origin
    Pulled and tested by JPC Mobile Brisbane

    Tools You Will Need

    Y00 Tri-Wing Driver

    For the four rear panel screws.

    PH00 Phillips Driver

    For the internal screws.

    Plastic Spudger

    To lift the flex cable connector.

    Anti-Static Mat

    Recommended to protect the motherboard.

    Need the tools? Browse our repair tool kits.

    Installation Overview

    1. Power off the console fully and remove both Joy-Cons.
    2. Remove the four Y00 screws from the rear panel.
    3. Lift the rear shield off and locate the rail flex connector.
    4. Disconnect the rail flex cable from the motherboard.
    5. Remove the screws holding the failed rail and lift it out.
    6. Fit the new sensor rail and reseat the flex connector.
    7. Reassemble and test Joy-Con detection and charging.

    Frequently Asked Questions

    Will this rail fit my Switch V1 and V2?+
    Yes. The HAC-001 (2017) and HAC-001(-01) V2 (2019) use the same sensor rail design. This pair fits both consoles. It does not fit the Switch OLED or Switch Lite.
    How do I know my Joy-Con problem is the rail?+
    Try a different Joy-Con of the same side. If the second one also fails, the console rail is the cause. If the second one works fine, the fault sits inside the original Joy-Con.
    Is this an official Nintendo part?+
    These are A-grade pulls. Original rails harvested from genuine Switch consoles by our Brisbane lab. Each pair is continuity-tested before dispatch.
    Does the pair include both left and right rails?+
    Yes. You receive one left console rail and one right console rail. Each is on its own flex cable and replaces independently.
    What tools do I need?+
    Use a Y00 tri-wing driver for the four rear panel screws. Use a PH00 Phillips driver for the internal screws. A plastic spudger lifts the flex connector.
    How long does the repair take?+
    Allow 30 to 60 minutes per rail at intermediate skill level. No micro-soldering is needed ā€” the rail simply unplugs and unscrews.
    Will this fix a Joy-Con that won't charge?+
    Yes if the swap test confirms the console rail is the fault. The rail's flex cable carries the charging current. A worn rail blocks that current.
    Does this fit Switch OLED or Switch Lite?+
    No. The OLED uses a different rail with a different connector. The Lite has fixed Joy-Cons and no rails. Browse our Switch OLED parts for that fitment.
    How fast do you ship in Australia?+
    All orders ship from Brisbane in 2 to 4 business days. We use tracked Australia Post or courier delivery.
    What warranty do you offer?+
    Pull rails carry a 7-day DOA cover from the date of delivery. Test the rail before reassembly. Damage from incorrect installation is not covered.

    šŸ’³ Pay your way ā€” Afterpay and Klarna available at checkout.

    Browse Related Categories

    Nintendo Switch Parts Switch OLED Parts Repair Tool Kits

    JPC Mobile Quality Seal

    Brisbane-stocked. Continuity-tested. Real Switch repairers on the other end of the email.

    šŸ“ Shop 3A, 152 Woogaroo St, Forest Lake QLD 4078 šŸ‡¦šŸ‡ŗ Ships Australia-Wide šŸ› ļø Tested Before Dispatch

    Payment Options

    We offer multiple convenient payment options for your repairs and accessories purchases. Pay with cash, debit/credit card, or interest-free Buy Now Pay Later options.

    Afterpay Zip Klarna PayPal
    Learn more about our Buy Now, Pay Later options ā†’

    Shipping & Processing Information

    Processing Time

    All orders require 2-4 business days for processing, regardless of shipping method.

    This includes order verification, picking, packing and preparation for dispatch.

    You will receive tracking information for all shipped orders and notification when pickup orders are ready for collection.

    Shipping Methods

    Standard: 3-7 business days in transit after processing

    Express: 1-2 business days in transit after processing

    Express shipping only affects delivery time once dispatched, not processing time.

    Express shipping does not expedite the 2-4 business day processing time.

    Nintendo Switch Console Sensor Rail Joy-Con Slide Rail Pair Left Right HAC-001 V2 Charging Flex Screen Replacement JPC MOBILE

    Nintendo Switch Console Sensor Rail Joy-Con Slide Rail Pair Left Right HAC-001 V2 Charging Flex

    $15.60