🛠️ Premium Repair Assembly
iPhone 15 Pro Max Back Glass
White Titanium Full Assembly
Complete rear restoration kit. MagSafe ring, wireless coil, sapphire lens covers, and reinforcement plate all pre-installed. Restore your White Titanium flagship to factory standards.
⚪ White Titanium 🧲 MagSafe Included 📦 Complete Kit 🇦🇺 Brisbane Stock
✅ In Stock 🛡️ 12-Month Warranty
📦 What This Full Assembly Includes
This is a full assembly — not just the glass. All five internal components are pre-installed. No transfers from your old back glass required.
⚪ White Titanium Rear Glass
Premium rear cover glass in Apple's White Titanium finish — the clean, pearl-tone colourway of the iPhone 15 Pro Max. Matched to the original factory colour.
💎 Sapphire Camera Lens Covers
Sapphire glass lens protectors for all three camera positions. Sapphire is among the hardest materials on earth — the same protection used in the original factory assembly.
🧲 MagSafe Magnets + Wireless Coil
The full MagSafe magnet ring and NFC/Qi wireless charging coil with flex cable are pre-installed. MagSafe chargers and accessories align and work normally after fitting.
🔦 Flashlight + Microphone Flex
The flashlight LED, flash diffuser, and rear microphone flex cable are part of the back glass assembly. All pre-installed — no delicate flex transfers needed.
⚙️ Steel Reinforcement Plate
The internal steel structural plate provides rigidity and ensures correct mounting of the wireless coil, bracket, and all sub-components within the assembly.
💡 Why full assembly matters: Glass-only kits require you to transfer the MagSafe coil, flash assembly, and flex cables from broken glass — high-risk steps with small components. This full assembly eliminates all transfers. You swap the entire module as one unit — faster, safer, and fewer steps where mistakes can occur.
⚠️ Professional Installation Strongly Recommended
iPhone 15 Pro Max back glass replacement is rated 7/10 difficulty. It takes 2–3 hours and specialist tools. One mistake can tear flex cables or crack the battery.
🔋 Battery Must Be Below 25%
Discharge your battery below 25% before starting. This is a safety requirement — a charged lithium-ion battery punctured during repair can ignite.
📏 5mm Maximum Pick Depth
Insert opening picks no deeper than 5mm when separating adhesive. Deeper insertion punctures the wireless charging coil or battery — causing permanent damage.
📐 5° Maximum Tilt
When lifting the back glass, tilt no more than 5°. The wireless charging coil flex cable is short — tilting further tears it from the logic board connector.
🔥 Heat Required
A heat gun or heating mat is needed to soften the back glass adhesive. Too little heat and the glass won't release. Too much damages the battery or screen adhesive.
🌊 IP68 Seal Is Broken
Opening the phone breaks the factory IP68 seal. Water resistance is only restored if fresh adhesive strips are correctly applied during reassembly.
🔧 Specialist Tools Needed
You need a P2 Pentalobe driver, Tri-point Y000 screwdriver, suction handle, opening picks, spudger, tweezers, isopropyl alcohol (90%+), and replacement adhesive strips.
💡 Bring it to us: JPC Mobile carries out iPhone 15 Pro Max back glass repairs in-store at Forest Lake Brisbane. Our technicians handle the full process — heat removal, flex cable disconnection, adhesive resealing, and IP68 restoration. Visit Shop 3a, 152 Woogaroo St, Forest Lake QLD 4078. Mon–Fri 9am–5pm · Sat 10am–5pm. Call 0480 039 913 to confirm part availability.
📦 In The Box
✅ 1× iPhone 15 Pro Max Back Glass Full Assembly — White Titanium
- White Titanium rear cover glass
- Sapphire glass camera lens covers (all three positions)
- Wireless NFC charging coil + MagSafe magnet ring (pre-installed)
- Flashlight and rear microphone flex cable (pre-installed)
- Internal steel reinforcement plate (pre-installed)
Not included: Installation tools, replacement adhesive strips, heat gun. Professional installation with proper adhesive resealing is required to restore IP68 water resistance after repair.
Frequently Asked Questions
Does this assembly include the MagSafe ring and wireless coil?
Yes — both are pre-installed. The MagSafe magnetic ring and NFC/Qi wireless charging coil with its flex cable are part of this assembly. You do not need to transfer these from your broken back glass. This is the primary advantage of a full assembly over a glass-only kit, which requires you to transfer the coil yourself — a risky process that can damage the coil or its flex cable during removal from cracked glass.
Is the White Titanium colour an exact match to the original?
This assembly is designed and colour-matched to the iPhone 15 Pro Max White Titanium finish — the clean pearl-white tone with subtle warm undertones that distinguish it from standard white. Minor colour variations can occur between manufacturing batches, which is normal for titanium-toned finishes. In most repairs, the colour match is very close to the original. If colour accuracy is critical, view the part in person before fitting — JPC Mobile can assist at our Forest Lake Brisbane store before you commit to the repair.
How difficult is the iPhone 15 Pro Max back glass replacement?
This repair is rated 7/10 difficulty — one of the harder iPhone repairs. It takes 2–3 hours and requires specialist tools. The most common failure points are inserting opening picks too deep (causing battery or coil puncture), tilting the glass too far during removal (tearing the charging coil flex at 5° or more), and applying too much heat (damaging the screen or battery adhesive). Professional installation is strongly recommended. JPC Mobile offers this repair in-store at Forest Lake Brisbane.
Will my phone be waterproof after the back glass is replaced?
The iPhone 15 Pro Max is IP68 rated (6m depth for 30 minutes) from the factory. Opening the phone breaks the factory adhesive seal — water resistance is not restored automatically. It can only be restored if replacement adhesive strips are correctly applied during reassembly. This is a step that requires skill and the right materials. A technician who specialises in iPhone repairs will apply fresh adhesive and restore functional water resistance as part of the repair — another key reason professional installation is recommended.
Why is a full assembly better than a glass-only replacement kit?
Glass-only kits require you to transfer the MagSafe coil, flash assembly, and microphone flex from the old (broken) glass to the new glass. These transfers involve removing small, delicate parts from cracked glass — one slip can damage the component. A full assembly eliminates all transfers. Every component comes pre-installed. You disconnect the old assembly at the connector, swap in the new one, and reconnect. The repair is faster, safer, and has fewer steps where mistakes occur.
What model number is the Australian iPhone 15 Pro Max?
Australian iPhone 15 Pro Max units are model A3106 (International variant). This assembly is compatible with all four regional variants — A2849 (USA), A3105 (Canada/Japan), A3106 (Australia/International), and A3108 (China). All four share identical back glass dimensions and internal component layout. The only differences between models are SIM configuration and cellular bands — the back glass assembly is the same across all variants. Check your model in Settings → General → About.
Do I need to discharge the battery before starting the repair?
Yes — this is a safety requirement. Discharge the battery below 25% before starting. Lithium-ion batteries are flammable under mechanical stress. The back glass removal process involves inserting tools around the battery area. A charged battery that is accidentally punctured or bent can ignite. Draining below 25% significantly reduces that risk. This step is mandatory in any professional iPhone repair process — not optional.
Does JPC Mobile carry out this repair in-store?
Yes. JPC Mobile offers iPhone 15 Pro Max back glass replacement at our Forest Lake Brisbane workshop. Our technicians carry out the full repair — heat removal, flex cable handling, MagSafe coil fitment, and adhesive resealing to restore water resistance. Visit Shop 3a, 152 Woogaroo St, Forest Lake QLD 4078. Monday to Friday 9am–5pm, Saturday 10am–5pm. Call 0480 039 913 before visiting to confirm part availability and turnaround time.
What does the 12-month warranty cover?
The 12-month warranty covers component defects on this assembly under normal use. If the back glass, sapphire lens covers, or any pre-installed component fails due to a manufacturing defect within 12 months, contact JPC Mobile with your order number and fault description. The warranty does not cover damage caused during installation — including cracks from incorrect fitting, flex cables damaged from overheating or over-tilting, or physical impact damage after fitting. Minor colour variation from the original is not a warranty fault.
How long does shipping take and how is the assembly packaged?
Orders are dispatched within 2-4 business days from our Forest Lake Brisbane warehouse. All repair parts are packaged in protective anti-static packaging to prevent damage to the flex cables, coil, and glass during transit. An Australia Post tracking number is provided on every order. Brisbane Metro typically receives orders 1-2 days after dispatch. Sydney and Melbourne receive orders within 3-5 days. Perth, Darwin, and remote areas typically take 5-8 days after dispatch.
🏪 JPC Mobile — iPhone Repair Parts, Forest Lake Brisbane
iPhone 15 Pro Max White Titanium back glass full assembly. MagSafe ring, wireless coil, sapphire lens covers, flash flex, and steel plate — all pre-installed. 12-month warranty. Ships Australia-wide in 2-4 business days.
📍 Forest Lake, Brisbane 📦 Complete Kit — 5 Parts 🛡️ 12-Month Warranty 🚚 2-4 Day Dispatch
Shop 3a, 152 Woogaroo St, Forest Lake QLD 4078 · Mon–Fri 9am–5pm · Sat 10am–5pm · 0480 039 913
