🔄 What is PULL-A Grade?
PULL-A means this part was pulled from a working console. It is not new. It is not aftermarket. It is an original Nintendo part that was tested and works perfectly. PULL-A parts cost less than new OEM but give you the same quality. Smart choice for repair techs who want reliable parts at fair prices.
🔧 Installation Recommendation
We recommend professional installation. This repair requires opening the Switch and removing the heat sink. You need Y00 tri-wing and Phillips screwdrivers. The ribbon cable connector is delicate. One wrong move can damage your console. If you are new to console repair, let a pro handle it.
Tools needed: Y00 tri-wing screwdriver, Phillips #00 screwdriver, plastic pry tools, tweezers
Frequently Asked Questions
What does PULL-A grade mean for this part?+
PULL-A means this part was pulled from a working Nintendo Switch console. It is an original OEM Nintendo part, not a cheap copy. Before we sell it, we test it to make sure it works. PULL-A parts give you the same quality as new for a lower price. This is how repair shops save money on parts without losing quality.
Does this fix both game card and headphone issues?+
Yes, this is a 2-in-1 part. The game card reader and headphone jack are on the same circuit board. When you replace this part, you fix both at the same time. If your Switch shows the "game card could not be read" error or your headphones don't work, this one part can fix both problems. You save money by not buying two separate parts.
Will this work with my Switch model?+
This part fits the original Nintendo Switch from 2017. Check the back of your console for model number HAC-001. This is the first Switch model. It does NOT fit the Switch Lite, Switch OLED, or the newer V2 Switch with better battery. If your model says HAC-001-01, it may not be compatible. When in doubt, contact us before ordering.
Do I need to solder to install this part?+
No soldering is needed. This part connects to the motherboard with a ribbon cable. You unplug the old one and plug in the new one. However, you still need to open the Switch and remove the heat sink to reach the connector. This takes skill and proper tools. If you have never opened a game console before, we recommend professional installation.
What causes the game card reader to fail?+
The most common causes are bent pins inside the card slot, dirty contacts, or wear from inserting and removing games many times. Kids often push cards in at an angle which bends the pins. Dust and debris can also block the contacts. Sometimes the reader just wears out over time. This replacement part gives you fresh pins and contacts.
Why did my headphone jack stop working?+
Headphone jacks fail for several reasons. The most common is a broken headphone plug stuck inside the port. Yanking the cable out at an angle can damage the internal contacts. Dust and pocket lint can also block the connection. Sometimes the jack just wears out from use. This replacement gives you a working port so you can use wired headphones again.
How long does the installation take?+
For an experienced repair tech, this takes about 30 to 45 minutes. For a first-time DIY person, expect 60 to 90 minutes. You need to remove the back cover, disconnect the battery, remove the heat sink and shield, and then access the card reader board. Take your time. Rushing leads to mistakes. Watch a guide video before you start.
What tools do I need for this repair?+
You need a Y00 tri-wing screwdriver for the back panel screws. You need a Phillips 00 or JIS 00 screwdriver for the internal screws. A plastic pry tool or spudger helps open clips and connectors. Tweezers are helpful for small cables. You may also want thermal paste if you remove the heat sink. We sell repair tool kits if you need them.
Can I test the part before fully assembling?+
Yes, and you should. After connecting the new part, reconnect the battery and test before you put everything back together. Insert a game card and check if the Switch reads it. Plug in headphones and play audio. If something is wrong, it is easier to fix before you close up the console. Only seal it up after you confirm everything works.
How is PULL-A different from aftermarket parts?+
PULL-A parts are original Nintendo parts. They came out of real Switch consoles. Aftermarket parts are new but made by third parties. They may look similar but the quality can vary. PULL-A gives you genuine Nintendo quality at a used part price. For game card readers, original parts often work better because the pin alignment and contact quality is exact.
Questions About This Part?
Our Brisbane team helps repair techs and gamers every day.
📍 Forest Lake, QLD 📞 0480 039 913
